Submit Tool → ⭐Write Review →
TECH TURF EDITORIAL & AI INSIGHTS

Renewable Energy Articles & Guides

In-depth software benchmarks, AI workflow tutorials, enterprise asset tracking insights, and expert reviews curated by the Tech Turf research team.

LATEST PUBLICATIONS

Recent Articles & Deep Dives

Sponsored
Advertisement

Category: Renewable Energy

Alternative Renewable energy – Clean and green power generation: Geothermal, Biomass, Solar Panel, wind, hydropower energy. solar power system electricity.

  • Monocrystalline Solar Panel Vs Polycrystalline Solar Panel

    Monocrystalline Solar Panel Vs Polycrystalline Solar Panel: A solar PV module is made up of connecting the multiple numbers of monocrystalline solar panels that are arranged in parallel sequence or in a series as per the requirements. All the products related to the modules are packaged and go through special production processes under the supervision of experts.

    The battery technology is different now as it is divided into crystalline silicon batteries, thin-film batteries and condenser batteries. So talking about the difference between monocrystalline solar panels and polycrystalline panels, there are many factors that vary in each of them and among them, one is battery technology. Both are two types of crystal silicon batteries but their arrangements differ from each other. The cost of polycrystalline is higher and that is the reason they are gradually decreasing. Over the years, there have been several developments in distributed photovoltaic and an increase in their demand for efficiency as well, so there is a rise in promotion for monocrystalline solar panels. 

    1. Main components of a battery 

    Photovoltaic glass: It is a low iron ultra-white flush glass that is usually 3.2mm thick and is often used in a battery. For the building of material type solar cell modules, tempered glass is used which is 5 to 10 mm thick but still transmit 90% of sunlight through it.  

    The content of iron in the low iron ultra-white glass is lower than the other ordinary glass and this enables them to transmit more sunlight from them. The tempered treatment to the glass helps in increasing the strength of the glass by 3-4 times more than normal glasses, resist more and provides long-term protection to the solar cells. 

    EVA film: The copolymer is a melted glue made of ethylene along with vinyl acetate and is used in a solar cell module package to bind them together. 

    The EVA film is a two-layer film that is set between the panel glass, the battery and the TPT backplane film. It helps in binding all three of them together so that it can help in improving the light transmission through them perfectly. This will further enhance the flow of light transmission and provide more power output from the cell modules. 

    Backplane material: The backplane materials may vary depending upon the requirements for the solar cell module. Usually, we have options such as tempered glass, plexiglass, aluminum alloy and TPT composite film. 

    The TPT composite film defines the characteristics of no breathable, good intensity, good weather resistance, long service life, and no change in lamination temperature, and is firmly combined with the bonding material. These characteristics of TPT composite film are suitable for These features are suitable for solar cell modules. It will effectively help in preventing erosion and influence various mediums like water, oxygen, corrosive gases on EVA.

    Junction box and bypass diode: Junction Box is an important component of a solar battery module and works as a part of the output cable and external cable. 

    A bypass diode is a part of the battery module that helps to prevent a part of a component or component in the square string that further blocks or stops from being shaded or causing power generation. It also protects the bypass assembly so as to avoid being at high.

    Cell: Crystal silicon solar cells are divided into two kinds of silicon cells that are mono crystal silicon cells and polycrystalline silicon cells. Usually, the positive electrode cable is considered as the negative electrode of the cell, and the electrode cable present on the back surface is considered as the positive cable of the cell. The total area of the cell is equally proportional to the output current and power generation. So the larger the area, the greater will be the output current and power generation. 

    1. The basic differences between the monocrystalline silicon and the polycrystalline silicon battery

    Monocrystalline cells and polycrystalline cells go under pre-production processes that have some variations from appearance to electrical properties. Like if we talk about the appearance: The four corners related to the monocrystalline cells are circular, and so there is no pattern of surface.

    And if we talk about the polycrystalline cells, there are four corners of it of the square angle, and the surface has a pattern that looks similar to an ice flower.

    For the customers, it might be in their mind that mono silicon cells and polysilicon cells are not very different or do not have major differences.  However, the average conversion efficiency of both does not have a major difference. The monocrystalline cells are only about 1% higher efficiency than the polysilicon cells.  

    Materials used for both the cells are different and that is the reason, the energy consumed during the manufacturing process of polysilicon cells is lower than the monocrystalline cells. This is the reason behind the low manufacturing cost of polysilicon cells and is more energy-efficient and environmentally friendly as well. 

    1. Component series

    Solar cells are connected in parallel series such as both series and parallel mix in several ways. During the battery module performance, each monomer is consistent and the array output voltage increases due to the series connection when we do not change the output current. 

    So when the components are connected in a parallel circuit, the output voltage of the array gets increased when there is no change in the output voltage. 

    And, when in series and the parallel is mixed, and the output current-voltage of the array then both can be increased. 

    In the square array combination connection, always follow the following principles: 

    (1) The components of the working current should be required in series, and the second poles should be connected in parallel to each component .

    (2) The same components of the working voltage should be required and connected to the anti-charge diode within each parallel line.

    (3) Always try to consider the shortest component connection cable and also use a coarser cable

    (4) Strictly prevent the cellular components that are not good to mix to the whole square array combination.

  • Solar PV Panel Manufacturing Method

    Solar PV panel manufacturing method: Below are the main methods by which solar panel can be manufactured. These methods are used by solar panel manufacturers around the world.

    Crystalline Solar Modules

    A solar PV module basically consists of solar cells, glass, back sheet and frame. Let’s talk about these terms in a bit more detail.

    There are certainly 3 types of solar panels available in the solar market:

    • Monocrystalline solar panels
    • Polycrystalline solar panels
    • Thin-film solar panels

    At the initial level of manufacturing the cell, there are different types of raw materials that are used such as mono silicon, polysilicon or amorphous silicon. The Monocrystalline and Polycrystalline solar panels have similar kinds of cells and their manufacturing process is also the same.  Below are the mentioned steps involved in the production of crystalline solar panels. 

    Step 1: Converting Sand into silicon

    The very first step involves the process of converting the sand to its useful form of silicon. Sand is the basic raw material and to the fact, solar panels are made up of silicon which is a component of natural sand. It is well known that silicon is the 2nd most available element on earth to date. Also, converting sand into silicon is an energy-intensive process but it often includes the high costs in production. Highly purified silicon is made at very high temperatures.

    Step 2: Formation of Ingots

    Once the silicon is collected in the form of rocks. Then these silicon is melted together at high temperatures and are formed as ingots which are shaped like cylinders. To make it look like exactly a cylinder, the furnace of a cylinder is used. The experts keep a check that during the production process, all the atoms should be perfectly aligned in a structure.  For providing the silicon with a positive electrical polarity, boron is used. 

    Now, moving towards Monocrystalline cells, these are manufactured from a single crystal of silicon. That is the reason mono silicon has higher efficiency while converting solar energy into electricity. Thus. making the monocrystalline panels more expensive and efficient. 

    Then, Polysilicon cells are made up of melting the silicon crystals together. This can be recognized easily by just looking at the shattered looks on glass. This is due to the silicon crystal present in it. Once the ingot is settled down and reaches the low temperature, they are polished and ground so that it gets a flat side.

    Step 3: Making the Wafers

    The next step is making out the wafers. These are the thin disks that have been sliced out from the silicon ingots. A wire saw is used for cutting it into disks and it is as thin as a piece of paper. Since the silicon is very shiny due to the presence of crystals in them, they can easily reflect the sunlight. Silicon wafers are covered with an anti-reflective coat so that they can absorb the maximum sunlight. 

    Step 4: Solar cells formation 

    There are certain processes involved in converting the wafer in solar cells that will be capable of converting the solar power produced into electrical power. 

    The wafers work as a metal conductor and are further added to each surface which gives a grid-like matrix form. This helps and converts solar energy into electricity. The coat provided to the wafer ensures that the cell absorbs maximum sunlight and does not reflect it back.

    Later, Phosphorus is diffused as in a thin layer over the whole surface of the wafers which enables the wafer to charge themselves with negative electrical orientation.  Earlier boron was used to charge positive electrical current so now the combination of both boron and phosphorus will work as a positive-negative junction and helps in the proper functioning of the PV cell.

    Step 5: Linking the Solar Cell to Solar Panel

    Then, the solar cells are arranged together by using metal connectors so as to link the cells in a matrix-like structure. Currently, the most common size used in Australian homes is the 6.6kWh solar system.

    Once the cells are arranged together, a thin layer of glass is added to its front side that faces the sun directly. Talking about the backsheet, it is made up of highly durable material that is based on polymer so as to protect the panels from water, soil, and other elements. Then the connection box is added so as to provide a connection to the PV module.

    Once the frame is assembled and settled down, it will provide protection from the weather. This will help in mounting or setting up the panels in different ways as well. 

    A very high-quality glue is used to bind every part altogether and it should not damage the cells during any bad weather conditions.

    Step 6: Testing the Modules

    Once the whole set-up is done, the testing process starts in which it is observed whether the cells are performing as it was expected or not. Standard Test conditions are taken into consideration while observing the performance.  All the electrical parameters are noted down so that you can find out the technical results on a paper about each panel separately.  The output ratings will declare the efficiency of the system, voltage, current, and temperature fluctuations.

    Apart from STC, many manufacturers use different tools to measure the cell temperature and the ratings. 

    Lastly, the final step is the cleaning and inspection process which states whether the system is ready to set up to homes or not. 

    Many researchers and solar experts are working hard to develop the solar industry. They aim to reduce the price of solar panels and increase the solar panel’s efficiency. Solar panel manufacturing industries have set up a tuff competition among themselves and are becoming more popular day by day. This often has increased the number of people who are switching to solar energy over other forms of electricity generation.

  • Top most Largest Solar Farms in the World

    Top most Largest Solar Farms in the World: There are so many solar farms in different parts of the world. A list of some of the renowned solar farms is given below along with a brief description that depicts the growth of the solar industry for years. 

    Largest Solar Farms in the World

    1. Bhadla Solar Park (India) 

    This is the largest solar park in the world and has a total capacity of 2,245 MW. This solar park is situated in the village of Bhadla which comes under the Jodhpur district of Rajasthan. This project is developing in four major phases and the total investment involved in this project is $1.4bn. 

    • The first phase (includes 7 power plants) and the second phase(includes 10 power plants) –  Rajasthan Solar Park Development Company Limited (RSPDCL) 
    • The third phase (10 solar plants) – Saurya Urja Company of Rajasthan
    • The fourth phase (10 solar plants) – Adani Renewable Energy Park Rajasthan

    The developers have been assigned for this project by NTPC and SECI

    2. Huanghe Hydropower Hainan Solar Park (China)

    This solar farm is situated in the deserts of Qinghai Province of China and has been developed by a state company named Huanghe Hydropower Development. The planning of this project is to reach 16 GW in future and it concludes 202.8 MW/MWh of total storage capacity which is huge itself. The project has been developed in 5 major phases The construction site has been connected to an ultra-high voltage transmission line that connects to different cities of China. 

    3. Pavagada Solar Park (India)

    This is officially known as Shakti Sthala Solar Power Project and is the second-largest solar farm in India. The project is spread over an area of about 13,000 acres having a 2GW solar complex. This solar project has been developed by the Karnataka Solar Park Development Corporation Limited which is a joint venture of Karnataka Renewable Energy Development and Solar Energy Corporation of India Limited. 

    4. Benban Solar Park (Egypt) 

    Benban Solar Park is Africa’s largest solar farm. Egypt’s largest 1.8GW solar farm is situated a few kilometers away from the south of Cairo. There will be around 7.2 million photovoltaic panels and it is said that this project can be seen from space. The total investment in this project is $4 billion and the main ambition is to increase power generation in Egypt. The project has been developed by the New and Renewable Energy Authority. 

    5. Tengger Desert Solar Park (China)

    Tengger Desert Solar Park is the second-largest solar park in China which is located in Ningxia. This project having a 1.55 GW solar complex provides power to more than 6,00,000 homes. This project is a joint venture of China National Grid and Zhongwei Power Supply Co. The project is spread in an area of 1,200 km of Tengger Desert. It is considered one of the most influential solar projects in China.  

    6. Noor Abu Dhabi (United Arab Emirates)

    Noor Abu Dhabi is a 1.2 GW solar park located in Abu Dhabi, UAE. This project will provide electrical power to 1,95,000 homes and will help to remove a million tones of carbon footprints in a year. The project often includes 3.2 million solar panels which are spread over 8 square kilometers. This project is a part of the UAE strategy which was launched earlier so as to increase the consumption of solar energy from the total energy generation. 

    7. Mohammed Bin Rashid Solar Park (UAE)

    Mohammed bin Rashid Al Maktoum Solar Park is situated in the United Arab Emirates and there are chances that it could climb up this list of solar parks in the future. The project is planned with a total capacity of 5 GW. It is stated that this project will probably cut down around 6.5 million carbon footprints each year. This project also includes houses for the Research and Development Center separately.  It has been set up with Jinko solar highly efficient solar PV panels. 

    8. Kurnool Ultra Mega Solar Park (India)

    This solar park is spread over an area of 24 square kilometres in a district called Kurnool of Andhra Pradesh. The capacity of this solar park is 1GW and is built with an investment of $980 million. The project is further developed by central and state governments along with solar developers. It has around 4 million solar panels that have capacities of about 315 and 320 kW. 

    9. Datong Solar Power (China)

    The Datong Solar Power Top Runner Base is among the biggest solar farms having a total capacity of 1.07GW. It is a long term project which will lead to a total generation capacity of 3GW in future. It generates around 870 million watts of electricity. It is the first national photovoltaic solar farm that has been approved by the Top Runner Program. The mission of this project is to promote the application of advanced photovoltaic technology and upgrade the solar industry. 

    10. NP Kunta (India)

    NP Kunta solar Park marks its position among the biggest solar farms in India with a total capacity of 978MW and is evenly spread in an area of 32 square kilometers. It is said that this project is planning to expand its total generation capacity in future to 1,500 MW. The main aim of this project is to support the government in managing the large-scale integration of renewable energy sources. 

    11. Longyangxia Dam Solar Park (China)

    Longyangxia Dam Solar Park comes in the list of large scale solar farms consisting of 850 MW capacity. This project consists of nearly 4 million solar panels and can provide power to 1,50,000 houses. It covers an area of 27 square kilometers and a total investment of about $8,895 million. The main aim behind this largest project is to limit the pollution level and increase the share of renewable sources in power generations. 

    12. Villanueva Solar Park (Mexico)

    Villanueva Solar Park is situated in the Viesca region of Coahuila, Mexico. The capacity of this solar park is 828MW and has been developed by Enel Green Power Mexico. The estimated investment for the project is around $710 million along with the construction divided into two phases. It will generate electricity that will be sufficient enough to power more than 1.3 million houses in Mexico. 

    13. Copper Mountain Solar Facility (United States)

    The Copper Mountain Solar Facility is a 552 MW solar plant which is located in Boulder City, Nevada. It acquired 1400 acres of land in the intense desert of Boulder City. It consists of 1 million solar photovoltaic solar panels that provide power to nearly 90,000 homes. The project was developed by Sempra Generation and aims to reduce tons of gas emissions so as to produce more clean energy. 

    14. Mount Signal Solar (United States)

    Mount Signal Solar plant basically consists of three solar plants that have been developed by 8minutes. It is also known as the Imperial Valley project situated in the west of Calexico, California. The total capacity of the project is 794MW and is planning to extend its generation capacity in future. This project was supported by several environmental groups as well. 

    15. Rewa Ultra Mega Solar (India)

    Rewa Ultra Mega solar is one of the largest solar plants situated in the Rewa district of Madhya Pradesh. It is spread in an area of 1590 acres having a capacity of 750MW and has been developed by Rewa Ultra Mega Solar Limited which is a joint venture of Madhya Pradesh Urja Vikas Nigam Limited and The Solar Energy Corporation of India. It has achieved a record for having low solar tariffs in India. 

    We hope that you have liked our article about largest solar farms around the world. If you have liked our article. Kindly share it with your friend via social media platforms.

  • How Does Solar Photovoltaic Energy Works?

    Solar energy absorbs the sunlight through the solar panels and then convert it effectively into electrical power. This electrical power is further used to run your home appliances or for business purposes. 

    Now, talking about it in brief, we all know that our sun is a natural source of energy for us. It releases tiny energy particles that are called photons. These photons travel a million kilometers from the sun to reach Earth in minutes. So every hour, there are enough photons that have an impact on our planet.  

    Solar panels do not generate electricity for the whole day but it generates when there is a requirement. Like it generates electricity during daytime or during sunny days as the demand is higher during that time.

    You will be amazed to know that Australia is considered one of the sunniest countries in the world. So in that case, it is a perfect place to put the panels for work and utilize the generated energy to the fullest especially during peak usage times. This generated electricity will work for all your appliances and makes you self independent. 

    How Do Solar Panels Work?

    Solar panels are basically a bunch of cells and multiple panels that are connected through wires makes an array. A solar panel includes two thin layers of silicon and has electrons.  So when the sun’s energy hits the panels, the electron gets hit from their atoms. A conductor is attached to the positive and negative sides of a cell so as to generate electrical current. The more numbers of panels you add to your array, the more energy will be generated. There is numerous kind of solar panels available in the market. 

    What are the Solar Panels Made up of?

    Photovoltaic (PV) solar panels are made up of silicon which works as a semi-conductor and are covered with a thin glass cover so as to protect them and the sun rays pass through filtration. It works just like a battery as it has both negative and positive layer that helps in creating an electric field to generate power. They are designed in such a way along with the glass cover that they protect the cells and minimize the damages that might occur to them in future. 

    How Does Solar Panels Generate Electricity?

    Simply elaborated, the cells present in the panels absorb light from the sun. When the sunlight touches the silicon part of the panels, the electrons start moving and generates electricity. The electrons flow in one direction moving around the circuit. 

    Let’s understand this step-by-step: 

    1. The photovoltaic cells present in the panels absorb the sun rays and converts them into direct current. 
    2. The solar inverter attached to the solar panels converts this direct current into alternating current. 
    3. This generated alternating current is used for your appliances and for other purposes. 
    4. If you have installed a grid-connected solar panel system, then the excess electricity generated will be sent back to the grid and you will be getting paid for it. 

    In Australia, alternating current is used for electrical power grids and is operated throughout the country. Thus, powering a large number of homes.  Since solar panels create direct current so, with the help of an inverter this direct current is converted to alternating current. 

    HOW DOES SOLAR INVERTER WORKS? 

    The basic function of a solar inverter is to convert the direct current into alternating current. It plays a very crucial part in a solar panel system and the whole mechanism depends on it. Apart from this, solar inverters provide several other functions such as fault indicator, system protection, voltage and current detector, energy production and maximum power output indicator. Though they are the less visible part of a system but play an important role in generating electricity. The inverter size depends on the size of the system and the number of panels. There are several types of inverters present in the market some of them are: Standard string inverter, Optimized string inverter, Microinverters and Hybrid inverter. 

    The growth of the central inverters can be seen throughout the passing years. But, the introduction of microinverters in the market has shifted the interest of the people towards the new technology in the solar industry. The main function of a microinverter is that it optimizes energy for each individual panel and does not works for the entire system. So this enables to get maximum output results from each individual panel to their maximum potential extent. Talking about central inverters, if one of the panels is facing any kind of problem like it is in shade or has dirt on its surface, then it will eventually affect the performance of the whole solar array. This as result, will affect the efficiency of the solar panel system. So, the best option is o opt for a microinverter so as to get maximum output. Even one of the panels is not working efficiently, the rest will not get affected at all and your system will continue to perform efficiently. 

    SOLAR PANEL SYSTEM MECHANISM: A BRIEF

    Let’s understand the mechanism step-by-step:

    1. The sunlight hits the solar panel array set up on your rooftop.
    2. The panel converts this sunlight into a direct current which then flows toward the inverter.
    3. The inverter converts this direct current into alternating current which can be used to power the appliances. 
    4. If you have a battery storage system attached to your solar power system, then the excess electricity generated will be stored in it and can be used later or during nighttime when the panels are not working. 
    5. If you don’t have a battery attached to your system then, the excess electricity will be transferred directly to the grid and you will be get paid for it in terms of credit points. 

    So, the mechanism of a solar panel system is very simple and produces clean energy which is an advantage for the environment as well. The part is that solar panel systems are getting more affordable day by day and it is getting the hassle-free process to switch to solar.

    You might have questions related to system generation that what happens when you are not at home during the daytime and your system is generating electricity? What happens when your panels are not generating electricity during nighttime? Well, a simple answer to all these queries is that you may get the benefit for the excess electricity generation in form of ‘feed-in tariffs’ and that depends on your energy retailer and state provisions. 

    A grid-connected system produces more energy than is required by the customer during peak times. So, this excess energy is transferred back to the grid to use for another purpose. The customer gets credit for generating excess power and this credit can be used to get conventional energy at night or during cloudy days. A feed-in tariff is described as a rate that is fixed for selling your solar power generated back to the grid. 

    Switching to solar will help you to make an impactful decision on your investment and save more. It will help you to contribute to saving the environment by switching to clean energy sources.

  • Switching To Solar: Feed-In Tariff

    Switching To Solar, Feed-In Tariff: With several new advancements in technology, experts are finding different ways to use renewable energy in cost-effective methods. We all know that solar energy is derived from sunlight and now we can use solar energy to power our houses.  Solar energy is generated with the help of sunlight by converting it into electric or thermal power. Apart from using solar panels so as to generate electricity, solar energy is generally used for thermal appliances so as to heat the indoor spaces.  Residentials and commercial property owners can install solar power systems by keeping passive solar heating in mind. They can design their buildings using solar technology and enjoy all the advantages of solar energy. Switching to solar energy will not only cut down your electricity bills but also will help in getting paid for the excess electricity your system generates. A solar-powered system absorbs the sunlight and converts it into usable electricity with the help of solar panels. 

    The Australian government provides huge support to the people who are switching to solar by providing them solar rebates. Also in addition they are giving feed-in tariffs to the citizens for the extra generated power by their system. This encourages the people to think about switching to solar, contributing to taking care of the environment and get the credit for it as well.  

    A very important point to be kept in mind while promoting renewable energy sources is the incentives that the customers get in form of feed-in tariffs. Since feed-in tariffs generally have long-term agreements which give a sense of security to the customers as they will get the benefits in future from switching to solar. The contracts are in a long-term period and have guaranteed prices as well so it provides a kind of shelter to the producers from some of the risks that are inherent in renewable energy production. This consequently encourages more and more people to invest in solar energy and enjoy several benefits. 

    Eligibility criteria for a feed-in tariff?

    The eligibility required for a feed-in tariff is that the customer needs to provide a source of renewable energy such as solar power by installing an on-grid solar power system at their house. As per the government incentive schemes, an ordinary homeowner can also enjoy the benefit of a grid-connected system. So this means, to use a renewable power source, you don’t need to be a commercial energy producer at all. They often include homeowners, business owners, farmers, and private investors. Basically, Feed-In Tariffs have three basic provisions-

    1. Feed-In Tariffs are for on-grid connections and they guarantee grid access all times to solar energy producers.
    2. Feed-In Tariffs offer long-term contracts, generally in the range of 15 to 25 years.
    3. Feed-in Tariffs offer guaranteed cost-based purchase prices. This means that the energy produced through the solar power systems that have been installed by the homeowners is paid for in proportion to the resources and the capital expended in order to produce the energy by the retailer they are connected to.

    Many retailers in Australia also introduced feed-in tariffs as a part of incentives so as to encourage people to switch to renewable energy sources to power their houses. The best advantage of the feed-in tariff is that it pays you for the excess electricity that your system generates. 

    There is a meter attached to your system that records the excess solar energy generated by your system and depending on that calculation by the meter, the homeowners can claim their feed-in tariffs. Also, the Feed-in Tariff may vary from retailer to retailer, so the homeowners have an option to switch to the retailer that offers more feed-in tariffs and a good deal for the extra power generated by their solar power system. 

    Under a net feed-in tariff, an amount fee is paid to the homeowner for any solar energy that they send back into the grid from their house. So if your system is generating more electricity from your solar panels than you are using at any point in time in your house, then you definitely get paid for this extra electricity that is sent into the grid. 

    The process of receiving the feed-in tariff is easy, your solar installer will apply with your electricity provider while getting the solar installation. Once your system has been installed, your electricity provider will connect your system with the grid. One of the important notes which should be kept in mind is that all the metering work is carried out by the electricity retailer. The solar provider does not have any role in it. Before signing the agreement, make sure to get the proper information about how much you will be paid for every kW/h that is exported to the grid. 

    It is always advised to be aware of the price set by their electricity provider as it may vary with the others. The customer should always check whether any change in tariffs by their retailers, changes may occur while installing solar. Get the proper knowledge about the advantages and disadvantages before making any final decisions. Just ask Future Solar’s expert team regarding any queries related to solar installations and feed-in tariff. 

    Feed-in tariffs are always priced based and so is the net metering as well. There are certain criteria in different countries to be eligible for receiving the feed-in tariff. So in order to qualify for this government incentive ‘feed-in tariff’, one should consist of the following options: an obligation of purchase, a stable tariff payment that is guaranteed for a long period of time. 

    Firstly, the purchase obligation obliges the connected grid operator to buy all the renewable electricity – independent of electricity demand. 

    Secondly, the renewable power producer, in this case, the homeowner, is guaranteed a certain amount of money per unit of electricity that their system produces.

    Thirdly, this payment is committed for a long period of time (around 15 to 20 years), which eventually increases the investment security and allows for cost settlement as well. 

    So there is a difference between feed-in tariffs and net metering as they both have different levels of functioning and provide different incentives while switching to solar. Net metering is also price based but in this, it is applied for promoting the decentralization of electricity power in different parts of Australia. Under this scheme, the independent power producers have the total right to get their system connected to the grid and the local utility is also obligated to purchase all excess electricity produced by the system. This simply means that all excess electricity generated that is not needed for local consumption has to be bought by the electricity retailer itself. 

    Meter measuring of electricity consumption is a support scheme. In this case, the meter starts turning back once it reaches the excess electricity level and fed it into the grid. Or in other words, we can say that for each unit of electricity that is delivered to the grid, the power producer receives the equivalent electricity price for it. Moreover, this electricity price for final consumers is not fixed. The net metering instrument lacks two of the most important features of the feed-in tariff and also offers a low-security investment. 

    Solar Feed-in tariffs should not be confused with other preferential tariffs as they have their own characteristics which mark their differences. In preferential tariffs cases, the remuneration level is fixed by the legislator. And as compared to a feed-in tariff mechanism, the tariff level is not guaranteed for a long duration. In fact, the legislator can change the remuneration level annually. So, it lacks one of the essential components of a feed-in tariff. 

    Nowadays, feed-in tariffs which are defined above briefly are generally applied in a large number of countries, regions and provinces. 

    So why are feed-in tariffs so good for you? 

    Firstly, they have proved that they are the best support mechanism for renewable electricity. Secondly,  they are flexibly designed according to the conditions and framework of the national electricity market and national policies. They can be modified so as to include electricity shares or according to the needs of the economy. Thirdly, feed-in tariffs lead to job creation as they have helped in creating national markets for the manufacturing industry. Lastly, they have contributed to the growth of energy markets by including small and medium-sized companies. 

    Interested in switching to solar power? 

    Solar panels are installed at two main scales: residential and commercial. 

    Residential-scale solar is basically installed on rooftops of the homes or in open land which is often called ground-mounted. The system size ranges between 5 and 20 kilowatts (kW), depending on the size and location of the property. 

    Commercial solar energy projects require large areas and are generally installed at a greater scale as compared to residential solar. Solar installations may vary in size, commercial-scale solar serves a different purpose: to provide on-site solar power to businesses and non-profits organizations. 

    Some people who might not be able to install solar at their houses may opt for community solar. It connects utility-scale solar energy projects to residential consumers. Community solar farms are basically built in the central locations and customers may opt for them to enjoy solar benefits even without installing the solar systems on their property.

Advertisement